The first thing most woodworkers think of when they think of power tools is a table saw, and for a good reason. A table saw can be used to make precision cuts, cut a wide variety of materials, and can be the backbone of any workshop.
But not all table saws are created equal, so it’s important to do your research before deciding which one is right for you. Read on to learn more about the best cast iron table saws on the market.
Our Editor’s Best Cast Iron Table Saws Reviews
1. WEN 3921 16-Inch Two-Direction Variable Speed Scroll Saw with Work Light
The design of this saw allows the user to insert the blade in either direction, allowing for more versatility and a larger range of motion. This saw has a variable speed that goes from 400 to 1600 strokes per minute.
The table is 16×11 inches and can be tilted up to 45 degrees to the left for angled cuts. The wood-chipper has a 16-inch throat depth and can cut wood up to 2 inches thick.
The scroll saw has a thumb screw blade adapter for easy blade changes, a cast iron base for stability, an air pump to keep the area clear of dust.
It has also a flex light to illuminate the work area, a dust port to connect a vacuum, a foot lock clamp to keep the saw in place, onboard storage for blades and other accessories, and three blades.
Read More: Best Corded Table Saws
2. DEWALT 10-Inch Cast Iron Table Saw, 32-1/2-Inch Rip Capacity (DWE7491RS)
Dewalt table saw comes with 24-tooth carbide blade, a rolling stand, a push stick, a miter gauge, a rip fence, 2 blade wrenches, and a blade guard assembly manual.
The other specs of this saw include the maximum rip to the left of the blade at 22 inches, the maximum rip to the right of the blade at 32-1/2 inches, the maximum width of the dado at 13/16 inch.
The arbor size at 5/8 inch, the amps at 15, the depth of cut at 45 inches at 2-1/4 inches, the depth of cut at 90 degrees at 3-1/8 inches, and the no load speed at 4800 RPM.
The rolling stand is designed for easy set up and breakdown, and is also very stable. This is a rack and pinion telescoping fence system that makes fence adjustments fast, smooth, and accurate.
This saw has a 15.0A motor that is powerful enough to cut through pressure treated lumber and hardwoods.
Read More: Best Table Saws Under $1000
3. Phenolic Zero Clearance Insert for Delta Uni-Saw Contractor | Large Grizzly and Other Table Saws with a 13-3/8” x 3-3/4” x 1/2” Throat Plate Opening
This insert is specific to table saws, and the shopper should measure their table saw insert or opening to compare to the size listed. The insert may also vary in color from what is shown in the image.
The Zero Clearance Throat Plate is designed to prevent smaller pieces of wood from getting caught between the saw blade and the factory supplied throat plate opening – which can cause the wood to jam up against the blade and go flying across the room.
If you’re looking to reduce tear out, especially when cutting plywood, then a zero clearance insert is a great option.
The insert essentially envelopes the blade on all sides, which doesn’t allow the wood to tear out since there is not gap between the blade and insert.
Zero clearance inserts can be used with most any table saw blade, including thin kerf, standard kerf, and carbide tipped blades. You can also use zero clearance inserts with dado blade sets.
The reason you would use zero clearance inserts with dado blades is to reduce the amount of tear out the dado blade set produces.
This insert is made from a durable phenolic material, has adjustable side tabs for a perfect fit, and features a top and side screw for a tight fit.
Read More: The 10 Best Table Saws Under $1500
4. Grizzly Industrial G0555 – The Classic 14″ Table Saw
This motor is 1 horsepower and is pre-wired for compatibility with 110-volt and 220-volt power sources. It uses 11 amps of power at 110 volts, or 5.5 amps at 220 volts.
The cutting height of this saw is 6 inches. (343mm). Right-tilt arbor for use with dado sets. This is a table saw that can cut through materials that are 13 and a half inches thick. The blade tilts to the right so that it can be used with a dado set.
The blade of this saw is made of ball bearings, which makes it run smoothly, and has upper and lower ball-bearing blade guides, which help keep the blade in place. This table saw includes a 3/8″ blade, extruded aluminum fence, and miter gauge.
5. SAWSTOP 10-Inch Contractor Saw, 1.75-HP, 30-Inch Standard Fence Assembly (CNS175-SFA30)
The SawStop patented safety system can stop a spinning blade on contact with skin in less than 5 milliseconds, potentially saving your life.
The Sawstop patented safety system will stop a spinning blade on contact with skin and drop below the table, minimizing a potentially life-altering injury to a mere scratch.
The Control Box on the saw checks that all systems are working properly to keep the user safe. The Contractor Saw is SawStop’s most configurable saw, with over 150 unique configurations possible.
You can add a mobile base, sliding crosscut table, or router table to make it just the right saw for your needs. The Contractor Saw is versatile and reliable, and is safe for a variety of users. It has a cast iron table top that creates better-than-hybrid performance in the shop.
This aluminum fence assembly is 30 inches tall and is designed for lightweight utility and accurate lockdown.
6. POWERTEC 71420 Table Saw Dado Insert Compatible with Ridgid R4512 10 inch Cast Iron Table Saw
This insert is for the Ridgid R4512 Table Saw and allows for dado cuts. The Ridgid R4512 Dado Throat Plate is a replacement for the dado throat plate on the Ridgid R4512 table saw.
It is made of premium materials and is a direct replacement for the original part. This saw insert is made of solid iron, is very flat for level cuts, and has a smooth, glossy finish.
The throat plate has non-countersunk adjustment holes and is held in place by a tab that clips the back of the plate to the table, preventing the table saw throat plate from popping up while in use.
The insert on this saw can be removed safely with a finger hole that is located away from the blade.
7. Magswitch 81101302 Vertical Featherboard Pro Table Saw Safety Attachment
This is a featherboard that will help to improve your cuts by holding the material down. This is especially useful on a table saw or bandsaw.
The Vertical featherboard is a professional woodworking tool that helps improve cutting results by holding down materials on a table saw or bandsaw. This makes it easier and more productive to use either of those tools.
This magnet is reversible, so it can be used on both sides of the workpiece. This featherboard is designed to keep your material in place while you cut it, ensuring precise cuts. It has magnets to keep it in place, as well as compressible gaskets for extra grip.
This saw has a clamp that can be attached to the center of a steel table saw fence or to any point on a steel tabletop. The interlocking tools can be used with different fence sizes.
